I dnt knw how but I think I managed to get wat I needed out of it so ta and the lil bits u did added a bit of funnyness to it so half a thumbs up? Lol I dnt hav any vids so and they wouldn't b as goood as that one.
I did this. Didn't really see a use for it being split. Just a quieter version of the same, with a little hum. I have 2 guitars. 1 with a humbucker, and 1 with P90. If you could split the humbucker and get a P90 sound THAT would be useful. But splitting it don't seem any different then just turning down the volume a bit. Unless you just love the hum.
Once u get a good soldering iron, its much easier and neater. . I was the same way. Ugly soldering. I bought a 40 watt Weller. It made the world of a difference.
I bend what you are calling the "third tine" down and solder it to the pot body. Simple and usually no need for any wire at all on that "third tine". The ground lug of the switch can also be bent back against the body of the switch and soldered. It makes for an overall much simpler and neater install.
This is a good simple video…..good job….just one question. I want to split the bridge and neck at the same time with the volume push pull pot. (it's a 5 way switch fender strat) Just connect the Red white from both pickups to the middle lug? Then connect the ground green /bare of both pickups to back of pot…..and black from both pickups to 1st lug on pot? Basically just connect both picks ups exactly the same way to the volume pot. The other thing is you split the coil but something from the pickup needs to go to the 5 way switch.
Hi I done your push pull one pot on my Les paul.can you please tell me how to get it so the split happened when you pull the pot not in close position.
Bring down the volume levels on your music it's masking your voice. It's also cheesy as hell why don't you play some guitar in the background instead? I see you cut it out later on, that's also a good call
I got a Seymour Duncan installed in the bridge of my Schecter with coil split. When I got it back, this was inverted on the new pickup. So humbucker mode on the bridge is single coil on the neck. How can I fix this? I have no experience and am soon to replace my neck pickup and don’t have the cash to pay for someone to do it.
I dnt knw how but I think I managed to get wat I needed out of it so ta and the lil bits u did added a bit of funnyness to it so half a thumbs up? Lol I dnt hav any vids so and they wouldn't b as goood as that one.
ew why would you put in old dirty gibson pickups to replace the SDs?
I have a question, I want to change the knobs of the coil split in my les
paul, but it is impossible, is there any way to remove these knobs?
I did this. Didn't really see a use for it being split. Just a quieter version of the same, with a little hum. I have 2 guitars. 1 with a humbucker, and 1 with P90. If you could split the humbucker and get a P90 sound THAT would be useful. But splitting it don't seem any different then just turning down the volume a bit. Unless you just love the hum.
Once u get a good soldering iron, its much easier and neater. . I was the same way. Ugly soldering. I bought a 40 watt Weller. It made the world of a difference.
I bend what you are calling the "third tine" down and solder it to the pot body. Simple and usually no need for any wire at all on that "third tine". The ground lug of the switch can also be bent back against the body of the switch and soldered. It makes for an overall much simpler and neater install.
Why solder to the top tho lol? Just solder to any of the outer casing..
I got all I needed to know just from the wiring diagram.
cool vid man you broke through the bullshit most vids go through diagrams and bs. nice.
I'll give you $40 and a six pack of Bud Light for those Duncans. Postage, too!
Could Push Pull Or Push Push Pots Work As Treble And Bass Control?
This is a good simple video…..good job….just one question. I want to split the bridge and neck at the same time with the volume push pull pot. (it's a 5 way switch fender strat) Just connect the Red white from both pickups to the middle lug? Then connect the ground green /bare of both pickups to back of pot…..and black from both pickups to 1st lug on pot? Basically just connect both picks ups exactly the same way to the volume pot.
The other thing is you split the coil but something from the pickup needs to go to the 5 way switch.
stop smoking so much pot before you make a video !!!! smoke on
Hi I done your push pull one pot on my Les paul.can you please tell me how to get it so the split happened when you pull the pot not in close position.
Bring down the volume levels on your music it's masking your voice. It's also cheesy as hell why don't you play some guitar in the background instead?
I see you cut it out later on, that's also a good call
I got a Seymour Duncan installed in the bridge of my Schecter with coil split. When I got it back, this was inverted on the new pickup. So humbucker mode on the bridge is single coil on the neck. How can I fix this? I have no experience and am soon to replace my neck pickup and don’t have the cash to pay for someone to do it.
Why did fart make me laugh?
Is that a 3 wire pick up ?